Feiyu-tech FY-31AP Bedienungsanleitung PDF herunterladen (Seite 4)

Guilin Feiyu Electronic Technology Co., Ltd

Guilin Feiyu Electronic Technology Co., Ltd http://www.feiyudz.cn E-mail: service@feiyu-tech.com Page 4

3-way switch or dial knob

blue

SW 2

Any free channel controlled by

3-way switch or dial knob

Channel 6

17. Vibration damping

A. FY-31AP is vibration-sensitive. To optimize its stabilization capability,

vibrations reaching the unit must be kept at a minimum.

B. When installing this flight stabilizer, we highly recommend that you

install it with the supplied vibration absorbing pads (dampers).

C. The algorithm in the FY-31AP compensates for normal levels of flight

vibration. However, if the vibration experienced by the unit exceeds

the acceptable level, it will not work normally or may even stop

working altogether.

D. To keep vibration at a minimum, install the FY-31AP away from the

engine or any other vibration sources.

E. The included shock-absorbing pads will

meet the damping requirements for

electric powered aircrafts and most gas

/ nitro planes.

F. The FY-31AP is supplied with the

double-sided foam padding dampers.

Please use them as shown:

 Checking for Vibration Levels

Even with the shock absorbing mount, your

aircraft installation may not meet the damping requirements of the FSS.

To confirm correct vibration damping, please follow this procedure:

A. After connecting all wires between the FY-31AP，Receiver and ESC,

install the unit as recommended (ensure correct orientation).

B. Run the plane engine or motor at different throttle levels. DO NOT

TAKE OFF.

C. Move the throttle level to different positions and maintain it for 20

seconds at each position.

D. At each throttle position, observe the state of the red LED light. If it

stays OFF, that means your vibration level is acceptable.

E. If instead the red LED lights up bright and stays ON solid, then the

vibration dampening is not enough. You will need reduce the level of

vibration on your aircraft, add additional dampening support or

change the installation location.

18. SW 1 and SW 2 : Switch Settings for FY31AP

a. SW-1 Flight Modes

The FY31AP has 3 Flight modes

controlled via SW-1. To select the modes,

use a free Receiver channel controlled via

a 3 way-switch:

FY-31AP flight modes

SW-1 signal output

900-1200us

1200-1800us

1800-2100us

Functional mode

Deactivated

Mode

Auto Stabilize

Mode

Navigation

Mode

Blue LED light

indicator

continuous flash

Stay on solid

Single flash

Note: Navigation Mode: means one of the three modes. Path Navigation mode,

Fixed altitude flight mode and Heading lock flight mode. You can select via the

GCS Software. The default mode is Path navigation mode.

b. SW-2 Autopilot Modes

FY31AP Autopilot Modes is controlled via SW-2.

IMPORTANT: The Autopilot Mode (SW-2) has controlling priority

over the Flight Modes (SW-1). If you wish to use the Flight Mode

(SW-1), you must de-activate the Autopilot first.

SW-2 signal

output

900-1200us

1200-1800

1800-2100us

Functional

mode

Return To Launch

Mode

(RTL)

Cancel

Mode

Auto Circling Mode

(ACM)

Blue LED light

indicator

Continuous Double

flash each loop

Continuous flashing.

3 times each loop

19. Plane connecting layout

1) FY-31AP connection for traditional aircraft layout:

AIL OUT

ELE OUT

THR OUT

RUD OUT

Aileron

Servo

Elevator

Servo

Throttle

Servo

Rudder

Servo

2) FY-31AP connection for flying wing aircraft:

(with or without Rudder)

AIL OUT

ELE OUT

THR OUT

RUD OUT

Differential

Servo 1

Differential

Servo 2

Throttle

Servo

Rudder

Servo

3) FY-31AP connection for V tail aircraft with Aileron:

AIL OUT

ELE OUT

THR OUT

RUD OUT

Aileron

Servo

Differential

Servo 1

Throttle

Servo

Differential

Servo 2

4) FY-31AP connection for V tail aircraft without ailerons:

AIL OUT

ELE OUT

THR OUT

RUD OUT

Differential

Servo 1

Differential

Servo 2

Throttle

servo

Null

5) FY-31AP connection for traditional layout aircraft with no Aileron:

AIL OUT

ELE OUT

THR OUT

RUD OUT

Rudder

Servo

Elevator

Servo

Throttle

servo

Null

6) Camera Gimbal Stabilization:

AIL OUT

ELE OUT

THR OUT

RUD OUT

Roll Servo

Tilt Servo

Null

Pan Servo

* Note: The camera gimbal Roll, Tilt and Pan servos will counter any

linear movement of the camera mount. You can move the camera at any

angle and upon releasing the stick, the FY-31AP will maintain

stabilization at that angle. The FY-31AP is only suitable for the camera

gimbal control which the control accuracy is not very high.

20. Connection of FY-31AP

900-1200us Deactivated Mode

mode

1200-1800us Auto Stabilization Mode

1800-2100us Navigation Mode

900-1200us Return To Launch Mode

1200-1800us Cancel Mode

1800-2100us Auto Circling Mode

1 2 3 4 5 6 7

Kommentare zu diesen Handbüchern

Keine Kommentare

Feiyu-tech FY-31AP Bedienungsanleitung Seite 4

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kommunikationszubehör Feiyu-tech FY-31AP